Short Answer
An energy balance around a boiler, turbine, or heat exchanger is only as accurate as the property values fed into it. For steam, everything hinges on the thermodynamic state: whether the steam is saturated — at its boiling condition for the prevailing pressure — or superheated — hotter than that boiling condition. The two states draw their enthalpy and other properties from different sections of the steam tables, so mixing them up corrupts every downstream result, from boiler heat duty to turbine power output. The diagnostic test is simple: compared with the saturation temperature at the steam’s pressure, a higher temperature indicates superheated vapor, an equal temperature indicates a saturated or wet state, and a lower temperature indicates compressed liquid. This article defines each state, explains why energy balances depend on choosing the right one, and walks through selecting the correct inputs with worked boiler and turbine examples.
Saturated and Superheated Steam: What the Terms Mean
The saturation point is the pressure and temperature at which liquid water and steam can coexist — the boiling condition. A saturated steam table lists these paired values: for each pressure it gives the corresponding saturation temperature, together with properties such as specific enthalpy (h) and specific volume (v) for saturated water (liquid) and saturated steam (vapor). These are tabulated separately because the substance can exist as either at the same pressure and temperature [3]. Data in a saturated table apply only to states on that boiling line — not to steam above it or water below it.
Superheated steam is vapor whose temperature is above the saturation temperature at its pressure. It has extra degrees of freedom: its temperature and pressure can be specified independently, and its properties come from dedicated superheated-vapor tables rather than the saturated section [2].
Between saturated liquid and saturated vapor lies wet steam, a two-phase mixture described by its quality (x), the mass fraction of vapor. Mixture properties interpolate between the saturated values — for example, h = hf + x·hfg, following the same pattern as the u = uf + x·ufg formula used in the standard steam-table procedure [2]. Below the boiling line, water whose temperature is lower than its saturation temperature for the given pressure is a compressed (subcooled) liquid — the usual condition of boiler feedwater [2].
Why Energy Balances Depend on the Correct State
An energy balance equates the energy carried into a system with the energy leaving it, typically through enthalpy differences. The boiler balance in a standard teaching example asks how much heat must be supplied to water at 19 °C to produce 66.45 kg of superheated steam at 560 °C and 16 MPa; the supplied heat follows from Q = m(h_admission − h_emission), where h_admission is the enthalpy of the superheated steam leaving the boiler and h_emission is the enthalpy of the water entering it [1]. Those two enthalpies come from entirely different regions of the property tables, and the balance changes the moment either state changes.
The same is true around a turbine: the power produced equals the mass flow multiplied by the drop in specific enthalpy between the admission and emission streams [1]. In the steam power cycle from which these balances are drawn, the working fluid passes through every state type in sequence — compressed liquid entering the boiler, saturated and then superheated vapor leaving it, and often wet steam exhausting from the turbine — so a single cycle calculation draws on several table regions at once.
How to Identify the State and Select the Right Inputs
The standard procedure for using steam tables reduces the selection problem to a small set of cases [2]. Applied to energy-balance work, it looks like this:
- Label every stream in the balance with the properties you actually know: pressure, temperature, and — for two-phase states — quality.
- Run the diagnostic test. Check the saturated water table at the given pressure to find the saturation temperature. If the given temperature is greater, the state is superheated vapor; if it is less, the state is compressed liquid; if it is equal, the state is a saturated condition — saturated liquid, saturated vapor, or a wet mixture [2].
- Pick the matching table region. For superheated vapor, go to the superheated tables and read properties at the given pressure and temperature. For compressed liquid, use compressed-liquid data; if the pressure is much smaller than the first entry in those tables, approximate with the saturated-liquid values (uf, and similarly hf) corresponding to the given temperature [2].
- Handle wet states explicitly. If quality x is known (0 < x < 1), the state is a mixture: combine the saturated-liquid and saturated-vapor values, for example h = hf + x·hfg [2]. If the state is saturated but you know only pressure and temperature, that pair alone does not fix the quality — another property is needed to distinguish liquid from vapor from mixture.
- Keep units and references consistent. Teaching examples commonly compute mass flow in kg/h and express specific steam consumption in kg/kWh [1]; confirm that pressures, temperatures, enthalpies in kJ/kg, and power in kW or MW are aligned before combining them.
A practical aid for the wet region is the enthalpy–entropy (h–s) chart, which lets you read mixture enthalpies directly without interpolating on quality — one reason turbine balance examples read admission and emission enthalpies ‘from the h–s chart’ [1].
Which Table Region Supplies Which Input
The following summary maps each possible state to its diagnostic test, its property source, and its typical role in a steam power plant.
| State | Diagnostic test | Property source | Typical role |
|---|---|---|---|
| Compressed (subcooled) liquid | T below Tsat at the given P | Compressed-liquid tables; saturated-liquid values at the given T when pressure is low [2] | Condensate and feedwater entering the boiler |
| Saturated liquid | T equals Tsat, x = 0 | Saturated tables, liquid columns (hf) | Water at boiling onset |
| Wet steam (two-phase) | T equals Tsat with 0 < x < 1 | Saturated tables combined through quality, e.g. h = hf + x·hfg; or an h–s chart [1][2] | Turbine exhaust |
| Saturated vapor | T equals Tsat, x = 1 | Saturated tables, vapor columns (hg) | Steam leaving an evaporator or boiler drum |
| Superheated vapor | T above Tsat at the given P | Superheated tables at the given P and T [2] | Turbine admission steam, e.g. 560 °C at 16 MPa [1] |
Worked Examples: Boiler and Turbine Balances
The following examples are adapted from energy-balance teaching material on the Clausius–Rankine cycle [1]; they illustrate state selection rather than complete numerical solutions.
Boiler balance: liquid in, superheated steam out
Question: how much heat must be supplied to water at 19 °C to create 66.45 kg of superheated steam at 560 °C and 16 MPa [1]? The boiler balance is Q = m(h_admission − h_emission). The first input, h_admission, is the enthalpy of superheated steam at the boiler outlet, read from the superheated tables at 16 MPa and 560 °C. The second, h_emission, is the enthalpy of the subcooled water near 19 °C entering the boiler, read from compressed-liquid data. The algebra is identical whatever the outlet state — what changes is which enthalpy the outlet state calls for. Had the boiler produced saturated steam instead, the outlet enthalpy would come from the saturated-vapor column at the boiler pressure.
Turbine balance: superheated in, wet steam out
Question: for a turbine of nominal power 100 MW admitting superheated steam at 560 °C and 16 MPa and emitting wet steam at 29 °C, what are the mass flow and the specific steam consumption [1]? The energy balance sets the produced power equal to the steam mass times the enthalpy drop, so the mass flow follows from dividing the power by (h_admission − h_emission), and specific steam consumption reports the steam used per unit of energy, in kg/kWh [1]. Note the states: the admission steam is clearly superheated, while the 29 °C exhaust is two-phase — at that temperature the saturation pressure is only a few kilopascals, deep in the wet region. The exhaust enthalpy is therefore a mixture enthalpy, which is why the source material reads both admission and emission enthalpies from the h–s chart [1]. Substituting the saturated-vapor enthalpy for a wet exhaust would overstate the enthalpy drop and understate the steam flow the turbine actually needs.
Common Mistakes When Choosing Steam Properties
- Using saturated values for superheated steam. Saturated tables apply only on the boiling line [3]. At 16 MPa, steam at 560 °C is far above the saturation temperature at that pressure (roughly 347 °C per standard tables), so it is superheated and must be read from the superheated-vapor tables [1][2].
- Treating saturated tables as a general steam database. A saturated table answers only one type of question — property pairs at coexistence, such as finding the saturation temperature for a given pressure [3].
- Ignoring quality in wet steam. Turbine exhausts are frequently wet; without quality, or without an h–s chart, the mixture enthalpy cannot be determined, and the saturated-vapor value does not represent the mixture [1][2].
- Mishandling compressed liquid. Feedwater below its boiling temperature is compressed liquid, not vapor. When the pressure is far below the first entry of the compressed-liquid tables, saturated-liquid properties evaluated at the given temperature are the accepted approximation [2].
- Assuming pressure and temperature always fix the state. They do for superheated and compressed-liquid states, but exactly at saturation the pair leaves the quality undetermined — an additional property is required [2].
- Unit slips. Mixing kg/h with kg/s, MW with kW, or quoting specific steam consumption in kg/kWh while the balance is in kg/s changes results by orders of magnitude [1].
Systematic plant-level analyses impose the same discipline. Published methodologies for steam boiler evaluation organize mass, energy, and exergy streams so that every input and output is identified and quantified before aggregate efficiency figures are computed [4] — the same habit that makes a hand-worked balance reliable: decide the state first, then read the properties from the matching region.
FAQ
How can I tell whether steam is saturated or superheated from pressure and temperature data?
Look up the saturation temperature for the given pressure in the saturated water table and compare. If your temperature is greater, the state is superheated vapor; if it is less, the substance is a compressed liquid; if it is equal, the state is a saturated condition — saturated liquid, saturated vapor, or a wet mixture whose quality must be determined separately.
Why can't saturated steam tables be used for superheated steam?
Saturated table data refer only to the boiling condition where liquid and vapor coexist at the same pressure and temperature. Superheated steam lies above that condition and needs the superheated-vapor tables, which list properties for independently specified pressures and temperatures.
What property inputs does a wet-steam turbine exhaust require?
A two-phase exhaust needs the mixture enthalpy, obtained either by combining saturated-liquid and saturated-vapor values through the quality x (h = hf + x·hfg) or by reading the enthalpy directly from an h–s chart, as standard turbine balance examples do.
Which steam-table values should I use for boiler feedwater?
Feedwater below its saturation temperature is compressed liquid. Use compressed-liquid tables; when the pressure is far below the tables' first entry, saturated-liquid properties evaluated at the feedwater temperature are the standard approximation.
Leave a Reply